WBD F 80 -T
WBD-P F 80 - 121/160
WBD-P F 80 - 161/200
WBD-P F 80 - 201/310
WBD F 80 - 80/120
End Support WBD F 80 HCP
Group: A421
Plug-in component for creating a square end plate at the open end of Beam Section TP F80 or Beam Bracket/Cantilever Bracket AK F80
Variation 'T' with octagonal insert allows full utilisation of the beam section within the space required by the End Support WBD
Overview of Types
General Information
Plug-in component designed to create a square end plate at the open end of a Beam Section TP F 80 or a Beam Bracket/Cantilever bracket AK F 80. The "T" variation with octagonal insert allows full use of the beam section, permitting screwed connections anywhere along the length without internal screw clashes.
Certification
CE mark (Declaration of performance see downloads)
ETA-24/0471
Technical specifications
Primary element material | steel |
Surface finish | HCP |
Corrosion protection class | C4 |
Load range
Type | -VX,perm. | VX,perm. | -VY,perm. | VY,perm. | -VZ,perm. | VZ,perm. |
WBD-4KT 80/120-F 80 HCP | 34,60 kN | 34,60 kN | 64,30 kN | 64,30 kN | 64,30 kN | 64,30 kN |
WBD-8KT 80/120-F 80 HCP | 47,00 kN | 47,00 kN | 56,80 kN | 56,80 kN | 56,80 kN | 56,80 kN |
Type | -MX,perm. | MX,perm. | -MY,perm. | MY,perm. | -MZ,perm. | MZ,perm. |
WBD-4KT 80/120-F 80 HCP | 3,7 kNm | 3,7 kNm | 5,2 kNm | 5,2 kNm | 5,2 kNm | 5,2 kNm |
WBD-8KT 80/120-F 80 HCP | 2,1 kNm | 2,1 kNm | 3,4 kNm | 3,4 kNm | 3,4 kNm | 3,4 kNm |
The specified load values are design loads Rd and include a partial safety factor γM2 = 1.25 (DIN EN 1993-1-8:2025-04, Table 4.1)
A partial safety factor of γG = 1.35 (DIN EN 1990:2021-10, Table A1.2(B)) must be taken into account for permanent loads.
Also available with DualShield for high corrosion protection within C5H environments.
Software
This product is available in the following software.
Installation
Depending on the situation, different options are recommended:
a) Directly to building structure: 4 x suitable wall anchors and 4 Self Forming Screws FLS applied to the square/octagonal insert
b) To traditional steel beams between 80 – 310 mm flange dimensions: 1 x Assembly Set 5P M12 S, M16 S and 4 Self Forming Screws FLS applied to the square/octagonal insert
c) To Sikla siMotec steel beams 100/120: with Bracket Plates FV 100/120 when positive mechanical connection required
The Beam Section TP F 80 connected to the End Support WBD F 80 has to be screwed with 4 Self Forming Screws FLS F. On each of the opposite sides 2 Self Forming Screws FLS F are necessary. The permissible distance between base plate WBD and profile must not exceed 30 mm.
Base plate finish:
| Type | Base plate finish |
|---|---|
| WBD F 80-80/120 | flat |
| WBD-P F 80-121/160 | corrugated |
| WBD-P F 80-161/200 | corrugated |
| WBD-P F 80-201/310 | corrugated |
| WBD F 80-T | flat |